各種空調使用中，都需要通風管道部件，它們是配合空調作業，利于空調運行的主要部件。而通風管道在使用中容易發生堵塞，為避免堵塞，在通風管道處理完畢后，我們可以做兩點預防，下面
濟南通風管道加工廠家為您解答。
In the use of various air conditioners, ventilation pipe components are required, which are the main components to cooperate with air conditioning operation and facilitate the operation of air conditioners. The ventilation pipe is easy to be blocked in use. In order to avoid blocking, we can take two precautions after the ventilation pipe is handled. Now, the ventilation pipe processing factory in Jinan will answer for you.
日常的檢查。通風管道加工完成后，我們可以不時地檢查一下通風管道的使用情況，當然，在檢查時要保證通風管道的通風效果，只有這樣，我們才能看通風管道是否有堵塞。如果通風效果不大，或通風效果不強，就應對其進行處理，避免產生更深的堵塞效應。
Daily inspection. After the processing of the ventilation pipe is completed, we can check the use of the ventilation pipe from time to time. Of course, we should ensure the ventilation effect of the ventilation pipe during the inspection. Only in this way can we see whether the ventilation pipe is blocked. If the ventilation effect is not large or strong, it should be treated to avoid deeper blockage effect.
定期進行清潔。值得一提的是，通風管道經過加工處理后，不需要再做任何處理，清洗處理是須的維護工作，它們既能保證這個管道長期使用，又能避免出現堵塞現象。因此說，我們要避免通通風管道堵塞，定期清理通通風管道是非常必要的。
Clean regularly. It is worth mentioning that after processing, the ventilation pipe does not need any further treatment. Cleaning is a necessary maintenance work, which can not only ensure the long-term use of the pipe, but also avoid blockage. Therefore, it is necessary to clean the ventilation pipe regularly to avoid blockage of the ventilation pipe.
空調的正常使用離不開通風管道，而通風管道在加工使用后會出現堵塞現象，對此，我們對其進行日常檢查并定期清洗，是避免堵塞現象發生的好辦法。
The normal use of the air conditioner can not be separated from the opening of the air duct, and the air duct will be blocked after processing and use. For this, we conduct daily inspection and regular cleaning, which is a good way to avoid blocking.
通風管道加工的過程中應該盡量避免出現縱向接縫，但是不能出現橫向接縫。而且通風管道的咬口縫和四角的縫隙處，需要按照設計潔凈等級要求，然后還要采用密封膠將其堵嚴。另外通風管道板材的連接縫的密封面應該設在通風管道壁的正壓側。
The longitudinal joint shall be avoided as far as possible during the processing of ventilation duct, but the transverse joint shall not be allowed. Moreover, the seaming seams and the four corners of the ventilation pipe shall be sealed with sealant according to the design cleanliness level requirements. In addition, the sealing surface of the joint of the ventilation duct plate should be set at the positive pressure side of the ventilation duct wall.
加工的時候，不能在通風管道內部設置加固框或者加固筋，因?yàn)檫@樣對于通風管道的質量會造成一定的影響。通風管道加工不能采用S型插條和C型直角插條的連接方式，另外對于一些特殊的通風管道來說，還不能采用按扣式的咬口。
During processing, reinforcing frames or reinforcements cannot be set inside the ventilation ducts, because this will have a certain impact on the quality of the ventilation ducts. The connection mode of S-shaped and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. In addition, snap joint cannot be used for some special ventilation ducts.
Therefore, if you have the operation of processing ventilation pipes, pay more attention to the maintenance and methods to avoid blockage after processing. If you want to know more about lampblack purifier and air purification, please pay attention to us http://m.yiruizhoucheng.com Come on!
上一篇：關于通風管道加工安裝時的五個要點
下一篇：油煙凈化器具體的安裝規范過程
